Testinside – IT certification exam World NO.1 IT Certification Exams Provider

Free Download PassQuick 4A0-110 Practice Exams

Preparing for the 4A0-110 exam? Searching 4A0-110 Braindumps, 4A0-110 Test Questions, 4A0-110 Practice Exam, 4A0-110 Dumps? PassQuick 4A0-110 is written to coincide with the real test by the experienced IT experts and specialists. With the complete collection of PassQuick Questions and Answers, PassQuick 4A0-110 is high enough to help the candidates to easy pass this exam easily without any other study materials and no need to attend the expensive training class.

Free 4A0-110 PDF Download

Download Alcatel Lucent 4A0-110 Pdf

　
　
Exam : Alcatel-Lucent 4A0-110
Title : Alcatel-Lucent Advanced Troubleshooting

1. Two routers are physically connected running ISIS. ISIS L2 adjacency is up and running but L1 adjacency is not up. Review the configuration information shown below:
Which of the following statement best describe the cause of the problem? Select one answer only.
A. The ISIS interface level is not configured on both routers
B. The ISIS interface type should be configured as point-to-point interfaces
C. ISIS System IDs are not configured on both routers
D. ISIS Area addresses are not configured on both routers
E. ISIS level capacity are not configured on both routers
Answer: D

2. A SDP is created on Node-2 with the far end address set to Node-3. The SDP stays down on Node-2. Based on the following CLI output from Node 2, what is the caused of the problem?
A. No LDP link session between Node 2 and Node 4
B. No LDP link session between Node 4 and Node 3
C. No LDP link session between Node 1 and Node 4
D. No LDP link session between Node 3 and Node 2
E. None of the above
Answer: B

3. Which of the following debug statements can be used to troubleshoot if the OSPF adjacency is staying at xstart state? Select two answers.
A. debug router ospf rtm
B. debug router ospf packet dbdescr
C. debug router ospf neighbor
D. debug router ospf packet hello
E. debug router ospf spf
Answer: BC

4. Based on the following configuration, which of the following statements are true? Choose all that apply.
A. No OPSF adjacency found on Node 1
B. Full OSPF adjacency between Node-1 and Node-2
C. Full OSPF adjacency between Node-1 and Node-3
D. Full OSPF adjacency between Node-1 and Node-4
E. OSPF is enabled on Node 1
Answer: BE

5. The LDP session is not down between Node-1 and Node-2. Based on the following configurations, what is the cause of the problem?
A. LDP targeted-session is enabled with no service configured
B. OSPF adjacency is not up between Node-1 and Node-2
C. Router id is not advertised by OSPF
D. LDP is disabled on Node-1
E. Traffic-engineering is not enabled on Node-2
Answer: C

6. Node A has an active BGP route 10.1.1.1 in its routing table, but the same route is not found in Node D routing table. Which of the following configurations are required to resolve this problem?
A. Add Interface X to OSPF on Node B as passive interface
B. Redistribute interface address Y and Z into BGP
C. ISIS Enable route-reflection on Node B
D. Enable next-hop-self on Node C
E. Enable route-reflection on Node C
Answer: AE

7. Two routers are physically connected to each other over Ethernet port 1/1/1. Review the configuration information below. What state should the OSPF neighbor be in?
A. INIT
B. EXCHANGE
C. EXSTART
D. FULL
E. No OSPF neighbor
Answer: D

8. Two direct connected routers are running RIPv2, neighbors are up but there is no route in the RIP database. Review the configuration information below. What is the potential problem?
A. System interface is not added to the RIP protocol
B. No import policy is configured
C. No export policy is configured
D. Split-horizon has to be disabled in RIP
E. Message-size has to be configured with a non-zero value
Answer: C

9. L1 ISIS adjacency is up between two routers (Node-1 and Node-2) with MD5 authentication configured. During a maintenance window, an operator was planning to change one of the ISIS hello authentication key from admin to admin123. After removing the hello authentication key from Node-1 (no change on Node-2 side), the ISIS adjacency stayed up. The operator decided to fall back to the original configuration and called Alcatel for support.
Which of the following statement best describe the cause of the problem? Select one answer only.
A. The ISIS hello authentication key was not configured properly in the first place, that’s why removing the authentication key does not impact the adjacency
B. The ISIS authentication key is the same as the hello authentication key, therefore removing hello authentication key does not impact the adjacency
C. The system interface is missing from the ISIS configuration, therefore ISIS is not working properly even before the change
D. ISIS hello authentication key is only used for hello packet exchange. It does not affect ISIS adjacency
E. ISIS hello authentication key is not used to bring up ISIS adjacency when traffic-engineering is enabled on the routers
Answer: B

10. Two routers are physically connected to each other with ISIS configured. No ISIS adjacency can be found on both routers. Ping works fine on the local and the remote interface addresses on both routers. Review the confguration information shown below.
Which of the following statements best describe the cause of the problem? Select one answer only.
A. The ISIS interface level configured does not match the ISIS level capability supported on the routers
B. The ISIS authentication check is enabled but there is no authentication type and password configured
C. ISIS Area addresses are not configured on both routers
D. L1 wide Metrics are disabled on the routers
E. ISIS Circuit id does not match on Node-1 and Node-2
Answer: C

11. Two routers are physically connected to each other over Ethernet port 1/1/ Review the configuration information shown below. What state should the OSPF neighbor be in?
A. INIT
B. EXCHANGE
C. EXSTART
D. FULL
E. No OSPF neighbor
Answer: E

12. What are the typical RIP related issues found during troubleshooting?
A. Interface filters
B. Broadcast/Multicast mismatch
C. Area id not match with neighbor
D. Group name not match with neighbor
E. Hop count too high
Answer: ABE

Recommended Training about Alcatel Lucent 4A0-110 testing Fromat

The following courses are the recommended training for 4A0-110 PDF Fromat.

4A0-110 Q & A with Explanations

4A0-110 Audio video download

4A0-110 Study Guide materials

4A0-110 Preparation Labs

4A0-110 paper books

4A0-110 rapidshare 4shared sadikhov links

4A0-110 torrent notes

4A0-110 self testengin

4A0-110 sample print pdf version

Why do you Choose PassQuick 4A0-110

Quality and Value for the 4A0-110 Exams

PassQuick Practice Exams for Alcatel Lucent Certification 4A0-110 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass 4A0-110 Exam

If you prepare for 4A0-110 exam using our PassQuick testing engine, we guarantee your success in the first attempt. If you do not pass the 4A0-110 exam on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.